ELICA ELN630SS Manuel télécharger pdf (Page 6)

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Have a

qualied technician install the range hood. It is the installer’s respon-

sibility to comply with installation clearances specied on the model/

serial rating plate. The model/serial rating plate is located behind the

left lter on the rear wall of the vent hood.

Canopy hood location should be away from strong draft areas, such

as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical Requirements”

section.

The canopy hood is factory set for venting through the roof or

wall. This range hood is not available for a Non-Vented (recirculating)

Installation. All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home Con-

struction and Safety, Title 24, HUD, Part 280) or when such standard

is not applicable, the standard for Manufactured Home Installation

1982 (Manufactured Home Sites, Communities and Setups) ANSI

A225.1/NFPA 501A, or latest edition, or with local codes.

Cabinet Dimensions

30” (76.2 cm)

36” (91.4 cm)

42 ”(106.7 cm)

19” (48.2 cm)

8½” (21.6 cm)

⁄16” (11.9 cm)

centerline

side

cabinet

side

cabinet

Vent and

power

supply cable

entry location

“A”: bottom of

canopy to cooking

surface

cooking surface

IMPORTANT:

Minimum distance “A”: 30” (76.2 cm) from cooking surface.

Suggested maximum distance “A”: 36” (91.4 cm) from cooking sur-

face.

The chimneys can be adjusted for different ceiling heights.

Venting Requirements

(Ducted models only)

• Vent system must terminate to the outdoors.

• Do not terminate the vent system in an attic or other enclosed

area.

• Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

• The length of vent system and number of elbows should be kept

to a minimum to provide efcient performance.

For the most efcient and quiet operation:

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24” (61 cm) of straight vent

between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps to seal all joints in the vent system.

• The vent system must have a damper. If the roof or wall cap has a

damper, do not use the damper supplied with the range hood.

• Use caulking to seal exterior wall or roof opening around the cap.

• The size of the vent should be uniform.

Venting Methods

This canopy hood is factory set for venting through the roof or wall. A

8” (20.32 cm) round vent system is needed for installation (not includ-

ed).

NOTE: Flexible vent is not recommended. Flexible vent creates back

pressure and air turbulence that greatly reduce performance. Vent

system can terminate either through the roof or wall.

Roof Venting

Wall Venting

A. Roof cap

B. 8” (20.32 cm) round vent

A. Wall cap

B. 8” (20.32 cm) round vent

C. 90° elbow

1 2 3 4 5 6 7 8 9 10 11 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

ELICA ELN630SS Manuel Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Hottes de cuisine ELICA ELN630SS