ELICA HOOD Manuel d'utilisateur télécharger pdf (Page 8)

Mounting

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

Description of the hood

Fig. 1

H. Interconnection cable

K. Control lever

Attention! The control lever is already supplied. It is to

be installed last, before connecting the hood to the

mains.

Insert the control lever into the apposite housing (see

drawings on the first pages of this booklet - triggered

connection, compulsory direction.

L. Halogen bulb

M. Lateral filter holder frame

N. Active carbon filter

O. Metal anti-fat filter

P. Anti-fat and carbon filters holder frame

Q. Filter holder frame releases

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

The hood is equipped with a “TOUCH SENSOR” device able

to determine the control of the lights and the speed when the

user touches the control bar. Read the instructions below

carefully for this purpose.

The cooker hood can be controlled through a remote control

available as accessory kit (see the paragraph relating to the

functioning of the remote control).

Automatic switch-on function

The hood is equipped with a temperature sensor that starts

the motor at the 1st suction speed (power) when the room

temperature around the hood is higher than 70°C.

The user can, however, switch off or modify the suction speed

(power). (See paragraph “Control of suction speed (power))”.

Control of suction speed (power)

The selection of the suction speed (power) is cyclical,

according to the speed sequences “”stand-by - 1-2-3-4- Stand

by -1-2-”… so that at every touch of the UPPER PART of the

control bar the suction speed (power) increases by a level

and then to switches off (stand-by) if the control bar is touched

again when the hood is at suction speed (power) 4.

It is possible lo turn the hood off (standby) even when the

hood is at any speed by pressing the UPPER PART of the

control bar (for more than 3 seconds).

It is possible to determine what suction speed (power) the

hood is in when the bar is equipped with a led that changes

colour on the basis of the suction speed (power), as follows:

Hood in stand-by: LED OFF

1st suction speed (power) - led GREEN

2st suction speed (power) - led ORANGE (amber)

3st suction speed (power) - led RED

4st suction speed (power) - led RED (FLASHING)

Note: the 4

aspiration speed (power) remains on for 5

minutes after which the aspiration motor positions itself on the

speed.

Touched once more, the suction motor switches off (Stand-

by).

Need to wash the anti-fat filter: GREEN led FLASHING

(read the instructions relative to “Reset and configuration of

the filters saturation signal")

Need to wash or replace the carbon filters: ORANGE

(amber) led FLASHING (read the instructions relative to

“Reset and configuration of the filters saturation signal”)

Note: reset can be carried out both with the control lever and

the remote control.

Control of the central light

The central light can be switched on and off by touching the

LOWER PART of the control bar BRIEFLY.

Control of the lateral lights (when envisaged)

The lateral lights can be switched on and off by touching IN A

PROLONGED MANNER the LOWER PART of the control

lever.

The PROLONGED TOUCH allows, other than switching on

and off, adjusting the intensity of the light emitted by the lamp.

Note: The functions of switching and off (and adjustment)

alternate.

The light intensity regulation feature is not available for hoods

with neon lights.

Reset and configuration of the filters saturation signal

Switch the hood on at any speed (see paragraph above

“Selection of the suction speed (power)”

Reset anti-fat filter saturation signal (GREEN LED

FLASHING on the control level)

First proceed with the maintenance of the filter as

described in the corresponding paragraph.

Touch in a prolonged manner (more than 3 seconds) the

UPPER PART of the control lever, the LED stops flashing to

indicate that the reset of the signal has been carried out and

the hood switches off.

Reset anti-fat filter saturation signal ORANGE (amber)

LED FLASHING

First proceed with the maintenance of the filter as

described in the corresponding paragraph.

Touch in a prolonged manner (more than 3 seconds) the

UPPER PART of the control lever, the LED stops flashing to

indicate that the reset of the signal has been carried out and

the hood switches off.

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

ELICA HOOD Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Hottes de cuisine ELICA HOOD